Same-day diagnosis, honest pricing, and a fix that lasts
Gas Dryer Flame Sensor Repair Saratoga CA You Can Count On
Gas Dryer Flame Sensor Repair Saratoga CA is what we do when your dryer tumbles but never heats. We test the sensor, the igniter, and the gas valve, then replace only the failed part. If your Whirlpool or LG runs a full cycle on cold air, call us today at +16693329106.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Flame Sensor Repair Includes
Every flame sensor job covers the full heat path, not just the part. Here is what is included in the flat price, and what we treat as a separate repair if we find it.
Multimeter Sensor Test
We test the flame sensor against the manufacturer spec and show you the reading. If the sensor passes, we keep testing until we find the real fault instead of replacing a good part.
New Flame Sensor Install
We install a manufacturer-spec sensor for your brand and model, torque the mounting screws, and confirm the probe sits correctly in the burner tube. The old part is left with you for reference.
Igniter and Thermal Fuse Check
Both parts sit in the same circuit as the sensor. We test the igniter glow and the thermal fuse continuity so a second failure does not send you back to the phone next week.
Gas Line Leak Check
We use a gas leak detector on the connector and valve after reassembly. Any leak gets repaired before we run the test cycle. This is a safety step, not an optional add-on.
Vent and Burner Cleaning
We vacuum the burner tube and brush the vent run. Restricted airflow is a common cause of repeat sensor faults, so clearing it protects the repair you just paid for.
Full Test Cycle
We run a complete timed cycle and watch the flame through the sight glass. You see heat working before we pack up, and you get a written summary of the repair and warranty.
Service overview
Gas Dryer Flame Sensor Repair Saratoga CA
Gas Dryer Flame Sensor Repair Saratoga CA is the diagnostic and replacement work that restores heat to a gas dryer whose flame sensor has failed. The flame sensor is a small metal probe that sits in the burner tube and confirms a flame actually lit. When it reads wrong, the control board shuts the gas valve within seconds, so the drum spins but the clothes stay damp. We test it with a multimeter, confirm the reading against the manufacturer spec, and swap the part.
Most Saratoga homes we visit sit on the west side of Santa Clara County, where cool mornings and long dryer cycles are the norm. A dryer that runs cold for a week straight usually means the sensor, the igniter, or a clogged vent is at fault. If you have been searching for gas dryer flame sensor repair in Saratoga CA near me and keep getting thin answers, we give you a real diagnosis and a real price.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How Our Flame Sensor Repair Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone Intake
You describe the symptom: drum turns, no heat, maybe a click but no flame. We ask for the brand and model, then book a two-hour arrival window. Most Saratoga calls get a same-day slot, and emergency gas dryer flame sensor repair Saratoga requests get priority.
On-Site Diagnosis
The tech pulls the dryer out, unplugs it, and shuts the gas valve. He removes the lower access panel and tests the flame sensor with a multimeter, then checks the igniter and thermal fuse. This takes 20 to 30 minutes and tells us exactly which part failed.
Quote and Approval
You get the finding in plain language plus a flat price for the fix. If the sensor is fine and the real fault is a blown thermal fuse or a clogged vent, we tell you that instead. You approve before any part comes out of the van.
Replacement and Reassembly
We install the new flame sensor, torque the mounting screws, and reconnect the gas line connector with a fresh seal. The burner tube gets a vacuum pass and the vent hose gets brushed out. Reassembly and leak check take another 20 minutes.
Test Cycle and Handoff
We run a full timed cycle and watch the flame through the sight glass. You get a written summary of what failed, what we replaced, and the warranty terms. We also show you the lint trap and vent path so you know what to keep clean.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Multimeter
Reads flame sensor microamp signal and thermal fuse continuity against the manufacturer spec. This is the test that separates a bad sensor from a bad igniter.
Manometer
Measures gas supply pressure at the valve inlet to confirm the burner is getting the pressure it needs to light and hold flame.
Gas Leak Detector
Sniffs the gas line connector and valve after every reassembly. Any leak gets repaired before we run a test cycle.
Thermal Imaging Camera
Spots hot spots and vent blockages behind the drum that a visual check would miss, especially on older Saratoga homes.
Vent Brush and Vacuum
Clears lint from the burner tube and the full vent run, restoring airflow so the new sensor reads correctly.
Nut Drivers and Screwdrivers
Pull the access panel and burner assembly without stripping the fasteners on Whirlpool, Maytag, LG, Samsung, GE, and Kenmore cabinets.
Putty Knife and Pliers
Free stuck burner tubes and handle gas line fittings cleanly during sensor and valve replacement.
Use cases
When to Call for Flame Sensor Service
These examples show how the service framework adapts rather than forcing every call through one repair.
Whirlpool Short-Cycling in Downtown Saratoga
A Downtown Saratoga homeowner heard the burner light and die within seconds, over and over. The igniter was fine, but the flame sensor could not confirm flame, so the gas valve shut down every cycle. The dryer never reached temperature. → We swapped the sensor, tested the gas valve coils, and confirmed steady flame through the sight glass. Cycle times dropped back to normal, and the dryer finished a heavy load in one run.
Kenmore No-Heat Before the Holidays in Quito Village
A Quito Village family called two days before a holiday with a Kenmore that would not heat. The flame sensor had failed, and a cracked gas line connector was leaking slightly. Two prior shops had quoted a full dryer replacement. → We replaced the flame sensor and the gas line connector, passed a leak check, and ran a full test cycle. Total bill came in under $400, and the dryer was working the same afternoon.
Problems we solve
Problems Our Flame Sensor Repair Solves
A bad flame sensor shows up in a handful of ways. If any of these sound familiar, the fix is usually quick.
Dryer tumbles but never heats
We test the flame sensor first, since a false reading shuts the gas valve within seconds of ignition. If the sensor is bad, we replace it and confirm the burner holds flame through a full cycle.
Burner lights then goes out after a few seconds
Our tech watches the flame through the sight glass and reads the sensor signal at the control board. A failed sensor gets replaced on the spot, and we test the gas valve coils while we are in there.
Dryer runs a full cycle on cold air
We diagnose the sensor, igniter, and thermal fuse together. If a clogged vent or lint trap caused the sensor to misread, we clean the full vent run and show you the airflow difference.
Clicking sound but no flame
We test each component in sequence with a multimeter and a manometer on the gas line. You get one clear answer and one flat price for the actual failed part.
Pricing process
What Flame Sensor Repair Costs
$180 - $450 depending on parts and access
Dryer Brand and Model
Common Whirlpool, Maytag, GE, and Kenmore sensors are inexpensive and usually on the van. Less common brands like Speed Queen or Bosch may need a special-order part, which adds a day and a small premium.
Access and Location
A garage dryer on a flat floor is a quick job. A stacked unit in a second-floor closet in Saratoga Hills adds 15 to 20 minutes of labor and a helper on some models.
Related Parts Found
If the igniter, thermal fuse, or gas valve coils also test bad, replacing them in the same visit saves you a second trip charge. We quote each part separately so you can decide.
Customer reviews
What Saratoga Customers Say
★★★★★
“Our LG was tumbling but the clothes came out cold and damp. The tech tested the flame sensor with a multimeter, showed me the bad reading, and had a replacement on the van. Total time was about 75 minutes and the price matched the quote exactly. He also brushed out the vent, which was half blocked.”
★★★★★
“Called at 7 a.m. about a Whirlpool that would not heat. They had a tech at the house by 10 and the flame sensor was swapped by lunch. What sold me was the honest diagnosis. He checked the thermal fuse and igniter first and did not just assume it was the sensor.”
★★★★★
“We had two other companies tell us to replace the whole dryer. These guys found a failed flame sensor and a clogged vent, fixed both for under $400, and the dryer has run perfectly for six months. They laid a drop cloth and vacuumed the burner area before leaving.”
How much does gas dryer flame sensor repair cost in Saratoga CA?
Most jobs run $180 to $450 in 2026, including the part and labor. The low end covers a straight sensor swap on a common Whirlpool or GE model. The high end covers a sensor plus igniter or thermal fuse replacement, or a hillside Saratoga home where the dryer is stacked and access takes longer. You get the exact number before we start.
Who repairs gas dryer flame sensors near me in Saratoga?
We do, and we cover all of Saratoga plus Santa Clara County. Our techs carry flame sensors for Whirlpool, Maytag, LG, Samsung, GE, Kenmore, Electrolux, Speed Queen, Amana, and Bosch. Call +16693329106 and we will book a two-hour window, usually the same day.
Can a gas dryer flame sensor be replaced same day in Saratoga California?
Yes, in most cases. If your dryer is one of the ten brands we stock, the repair finishes in a single 60 to 90 minute visit. We confirm part availability when you call, so you know before we arrive whether it is a same-day fix or a next-day return.
How do I know if my gas dryer flame sensor is bad in Saratoga?
The classic sign is a drum that tumbles but never heats, with the igniter glowing and then going dark after a few seconds. You may hear a click as the gas valve opens and closes. A multimeter test confirms it. If the igniter never glows, the fault is more likely the igniter or thermal fuse.
Related services
Related Services
Gas Dryer Repair
When your dryer needs more than a sensor, our full gas dryer repair covers the burner assembly, drum, and controls. We diagnose the whole appliance in one visit so you are not paying for two trips to Saratoga.
Gas Dryer Not Heating Repair
No heat is the number one symptom of a bad flame sensor. We trace the entire heat path, from igniter to gas valve to sensor, and fix the actual cause instead of swapping parts until something works.
Gas Dryer Not Spinning Repair
A dryer that heats but will not tumble points to a drive belt, drum roller, or motor fault. We handle both problems in one visit when Saratoga customers call with a dryer that neither heats nor spins.Ready when you are
Book Gas Dryer Flame Sensor Repair Saratoga CA Today
Damp laundry piles up fast. Call +16693329106 and we will book a two-hour window, usually the same day. Flat pricing, 12-month warranty, and a full test cycle before we leave. Saratoga, CA homeowners get priority scheduling on no-heat calls.
Talk with the local team
Request Gas Dryer Flame Sensor Repair
Call us at +16693329106 or email [email protected]. We answer calls 24/7 for emergencies and schedule same-day service Monday through Saturday. Our office is in Saratoga, and we serve the whole Santa Clara County area.